Yahoo Search Búsqueda en la Web

Resultado de búsqueda

1. www.corvetteforum.com › forums › c4-tech-performance1996 LT4 crankshaft position sensor location - CorvetteForum ...

   www.corvetteforum.com › forums › c4-tech-performance

   • En caché

   27 de may. de 2017 · Received 1,706 Likes on 1,292 Posts. To answer the OP's original question, the crank position sensor is at the bottom of the timing cover, right behind the balancer. It points up at the trigger wheel from the 6-o'clock position. You'll see an electrical connector it. It isn't the easiest thing to access in a C4, though.

2. www.corvetteforum.com › 3669857-crankshaft-sensor-replaceCrankshaft Sensor Replace - CorvetteForum - Chevrolet Corvette...

   www.corvetteforum.com › 3669857-crankshaft-sensor-replace

   • En caché

   19 de jun. de 2015 · C6 Corvette General Discussion - Crankshaft Sensor Replace - Just came back from the dealer. I have a very small oil leak they say is coming from the crankshaft sensor and it needs to be replaced. The leak is so small, it does not drip. I just happened to notice it when I was changing the oil and saw an oil film on...

3. www.digitalcorvettes.com › threads › crankshaft-position-sensor-reallyCrankshaft position sensor REALLY - Corvette Forum

   www.digitalcorvettes.com › threads › crankshaft-position-sensor-really

   • En caché

   27 de jul. de 2011 · 134 posts · Joined 2006. #1 · Jul 27, 2011 (Edited) Crankshaft position sensor REALLY "CODE 41?" I read that there is no crank sensor on a 94 LT1, I have a service manual that said there is one but I can't find it where it said it was. :thud: Am I missing something. Car has been sitting for 4 months and I'm lost.

4. www.samarins.com › glossary › crank_sensorCrankshaft position sensor: how it works, symptoms, problems,...

   www.samarins.com › glossary › crank_sensor

   • En caché

   1 de ago. de 2022 · As the crankshaft rotates, the sensor produces a pulsed voltage signal, where each pulse corresponds to the tooth on the reluctor ring. The photo below shows the actual signal from the crankshaft position sensor with the engine idling. In this vehicle, the reluctor ring is made with two missing teeth, as you can notice on the graph.

5. www.yourmechanic.com › symptoms-of-a-bad-or-failing-crankshaft-position-sensorSymptoms of a Bad or Failing Crankshaft Position Sensor

   www.yourmechanic.com › symptoms-of-a-bad-or-failing-crankshaft-position-sensor

   • En caché

   6 de ene. de 2016 · Usually, a problematic crankshaft position sensor will produce any of the following 7 symptoms that alert the driver of a potential problem that should be serviced. 1. Issues Starting the Vehicle. The most common symptom associated with a bad or failing crankshaft position sensor is difficulty starting the vehicle.

6. www.youtube.com › watchLS Crankshaft Position Sensor Replacement - How To - YouTube

   www.youtube.com › watch

   • En caché

   25 de sept. de 2021 · If you had a check engine light that was diagnosed as P0335 Crankshaft Position Sensor. The LS engines crank sensor is located on the passenger side of the e...

7. www.corvetteforum.com › 1506374-96-lt1-crank-position-sensor-relearn96 LT1 Crank Position Sensor Relearn - CorvetteForum

   www.corvetteforum.com › 1506374-96-lt1-crank-position-sensor-relearn

   • En caché

   23 de sept. de 2006 · A friend has a 96 LT1 engine and a swapped out PCM from a tuner. It keeps throwing a code for the crank position sensor - P0336: Crank Position Sensor Performance. According to the programmer it is common with PCM swaps. I put a TECH2 on it and the CKP is working. According to the Service Manual it triggers when the engine rpm and the CKP ...